baffling as it is , drywall can withstand only modified insult . If you open a door with too much force , it can thrash into the wall , create a make a doorknob - size hole into the drywall . This kind of wrong look sorry , but is easy to fasten . The simple means is to buy adrywall stamping ground kit . Measure the hole , and visit your local ironware shop or household improvement shopping mall for a outfit , or corrupt one online . There are various size of it and types for different applications . For object lesson , a drywall patch for a ceiling is thicker than one for a rampart . Before you use the kit , remove any loose newspaper or plaster around the edge of the hole . Then apply drywall patch , following the manufacturer ’s instructions .
In this article , we ’ll tell you how to mend both a belittled and a large drywall hole . We ’ll start with a little hole .
Fixing a Small Hole
To make a mending to a small drywall hole , about 6 column inch ( 15 centimeters ) or so , without a outfit , follow these commission :
Step 1:
The first matter you need to do is get a piece wallboard that is the same heaviness as the drywall you ask to fix . If you do n’t have any at dwelling , a hardware store will have smaller pieces that you may use . No need to buy an entire sheet .
Step 2:
Measure the patch . It should be big enough to extend the trap and then some . Give yourself a lot of wiggle elbow room — about 2 inch ( 5 centimeters ) on each side of the hole . You do n’t require the darn piece to be too belittled . Next , cut the while square from the larger piece . Turn the patch over and using a straight edge to score the composition back about an inch ( 2.5 centimeters ) from each side with a public utility knife . Do n’t tailor all the way through the paper or the gypsum . Next , snap off the loose drywall , but leave the loose paper on the back . Place the patch over the gob in your wall and utilise a pencil to trace it ’s outline around the gypsum ( do n’t include the paper flow over when you are delineate ) .
Step 3:
Let ’s pick the hole in the wall up . If you have a drywall saw , bully for you . That ’s the right-hand putz to have . If not , do n’t worry . you could habituate that utility tongue . no matter of what blade you utilise , cut slanting lines emanating from the hole to all four corners of synopsis you just traced . This will create a decent square opening . ( You do n’t have to cut diagonally to the recession , although it is easier . Just cut back out the damage portion of the drywall . ) If you do trim back diagonally to the corners , you ’ll also need to score the outline of the square with the utility tongue . Once make , snatch the pieces of dry wall back , and then make out the edge with the public-service corporation knife and pull out the drywall so you have a nice , clean square hole .
Step 4:
Next , wrick the while slice face down and apply a thin coating of joint compound to the back of the paper using a putty knife . Turn the patch over . Put the mend over the hole , pressing down on the paper edges . ensure it ’s a secure conniption . The joint chemical compound will hold the patch in place .
Step 5:
Finally , using a putty tongue , apply joint compound on the spot , diffuse it out on the rampart , as well . It might take two or more coat of chemical compound . It spreads easily , and well , is kinda fun to work with . When the chemical compound prohibitionist , sand it smooth with a fine - grain piece of sandpaper . The patch is set up for priming and painting .
Fixing a Large Hole
lease ’s say the maw you have is reasonably with child . peradventure it ’s a good - sized fix in a wall between two studs . Perhaps you hit the brakes a chip late and mosh into the back bulwark of the service department . No worries . you could ready it , too . And it ’s relatively well-off .
contract out a large square while of wallboard that will fit between the stud poker . This will be your patch part . put the square patch over the hole , just like the instruction call for in repairing a small hole . Using a pencil , trace around the edges of the patch .
Use a service program tongue to score along the lines you just traced . You do n’t have to cut too deep . It will make the next step easy . Using a unbent edge and a drywall tongue — a utility tongue is harder to use in this post — cut and remove the gypsum from the damage drywall . ( Important safety top : As you unclothe the drywall away , verify you unwrap the studs . ) Smooth the rough edges of the drywall with sandpaper .
Since the opening is between two stud , you’re able to simply place the patch over them . Screw the patch onto the studs using drywall screws and a power drill .
Place a few strips of mesh drywall over the edges of the patch . The mesh will have a sticky backing , so it ’s easy to put on . Cut the overhang with the utility tongue . Next , using a putty tongue spread joint chemical compound over the mesh and heads of the screws .
Once the chemical compound is dry , sandpaper it down and remove any liberal compound . The repaired wall is now quick to be primed and paint .
© Publications International , Ltd.
