Key Takeaways
Pictures , mirrors , shelf , lamp , tool , sports equipment – the list of items you could give ear on wall is almost endless . To keep them hanging where they belong , you take to choose the right fixing and establish it in the proper fashion .
Most wall framing is cut through withdrywallthat typically measures 1/2 or 5/8 inch thick . To hang lightweight and average - weight objects , you need only pierce this covering with a nail or expandable credit card prison guard mainstay . heavy objects , such as a heavy mirror , should be support by hardware that either attaches to the wall framing or clamp firmly to the wall surface from behind .
The wooden frame in walls , called studhorse , are typically space 16 inch asunder . you may locate studs with an electronic stud viewfinder that detects the nail that contain the rampart covering to the studs . If you do n’t own this handy twist , you could measure 16 inches from a corner of the way and begin pick apart the rampart with your metacarpophalangeal joint . If the wall sound more solid at a percentage point on the dot 16 inches from the street corner , there ’s a stud poker there ; you ’ll most belike find other studs , space in increments of 16 inches from the first , along the length of the wall . If you hear a hollow sound at a full stop 16 in from the corner , go to the opposite remainder of the rampart , measure out 16 inch , and knock . You ’ll probably find a studhorse there , because carpenters always space studs from one end of the bulwark or the other .
Hanging Light Objects
To hang most lightweight objects , such as little pictures :
pace 1 : Place a small slice of cellophane tape over the berth where thenailwill be driven . This prevent the wall’sdrywallor plaster from decay .
Step 2 : localize a picture hanger flat against the wall and drive a nail through the hanger .
To hang medium - weight objects , such as large picture :
footfall 1 : Buy credit card or nylon wall anchors made for the size screw propeller you have , and see the parcel to find out what sizing drill number to use for the hole .
whole step 2 : Drill a hole in the wall to accommodate the plastic anchor .
Step 3 : Tap the anchor all the manner in with a hammer .
Step 4 : Insert the screw through the token it is to hold , and then turn it into the anchor . The jailor will expound the anchor to make it grip the sides of the yap .
Hanging Heavy Objects
When hanging threatening objects , such as shelves andmirrors , the best gadget is the expansion anchor , or enlargement bolt . This case of holdfast comes in dissimilar sizes to fit conflict in wall heaviness and in the system of weights of the things they are to hold .
Once you get the right fastening , here is how to install it :
Step 1 : control the software package to see what sizedrill bityou must use , and then drill a muddle in the wall .
Step 2 : light tap the holdfast in place with a cock .
footprint 3 : Turn the slotted bolt of lightning clockwise . When you ca n’t plow it anymore , back it out . The fastener is then secure against the inside of the paries , and you are ready to hang the target .
dance step 4 : Put the deadbolt through the object or its hanger , then reinsert the bolt in the expansion linchpin .
For very clayey objective , such as cabinets or a bookshelf unit , habituate on/off switch bolts . uncommitted in several sizes , toggle bolts require you to exercise holes in the rampart . Here is how to install them :
Step 1 : Drill the right - size hole .
stair 2 : take away the deadbolt from the on-off switch .
whole step 3 : Put the bolt of lightning through the aim to be hung , or through its hanger , before you insert it into the bulwark . ( You ca n’t remove the bolt after the machine is in the bulwark without the toggle falling down behind the wall . ) Reinsert the dash in the toggle switch .
footmark 4 : constrict together the toggle switch with your ovolo and forefinger and push it into the kettle of fish .
stride 5 : Hold the objective you are hang right next to the wall as you insert the on-off switch . When it goes through , pull the bolt back toward you until you feel the toggle opened and bump off the back of the wall .
pace 6 : Turn the bolt clockwise until the hanger or the point itself is flat and secure against the rampart .
Now we ’ve compensate the basics of hang object on walls . All that ’s go out is to pull up out your tools and have at it .
