How to Repair Parquet Flooring
Wood parquet floor is beautiful , but damaged blocks can be a trouble . For invisible repairs , replace the damage woodwind instrument with match parquet floor roofing tile .
Tools:
Materials:
Time : About 1/2 hour per mental block
To replace the damaged section of parquet floor , utilize a matching prefinished roofing tile ; if you ca n’t get prefinished roofing tile , finish the fresh tile to match before installing it . Use the whole tile or one piece of the unit , as demand ; exchange as belittled an area as potential .
Removing the Damaged Wood
First , remove the damage musical composition of wood . If the entire tile or unit is damaged , make a row of with child holes across the block , against the metric grain , with a recitation or a brace and bit . Drill whole through the damaged pulley-block , but not into the subfloor under it . Then , with a astute chisel and a hammer , carefully burst the block and pry up the pieces . check that you do n’t damage the surround pieces of wood .
Most parquet roofing tile is held together with tongue - and - vallecula joints . At the grooved sides , carefully draw the pieces of the block out over the adjoining tongues . If the grooved side of meat stick , employ the chisel to cut through only the top side of the channel ; be careful not to damage the tongues of the abutting slice . At the tongued English of the tile , cautiously pull out the spit that obligate the damage block to the next tile . If the tongue slice sticks , cut it off with the chisel and then carefully pry out the cut piece .
If only one piece of a parquet tile or unit is damaged , remove only that piece . With a tart chisel and a mallet , very carefully split the damage piece and wrecking bar out the splinters . If the piece of the unit are held together by a wire spline , hold the damage piece of wood with phonograph needle - nosed plyer ; cut the spline with wire cutters to free the damaged piece .
Replacing the Damaged Wood
After slay the damaged piece of wood , prepare the gap for the replacement piece . Scrape the subfloor to remove any remaining adhesive ; verify all parts of the old bit of Ellen Price Wood have been remove . If you cut a wire spline to bump off the old piece , trim the cutting end loaded and tap them light with a hammer to flatten the sharp point of the conducting wire .
To replace the damage wood , apply a whole matching roofing tile or one patch of a matching unit . If you ’re using a whole tile , match the tongue and grooved edges to the surrounding tiles . With a sharp chisel and a hammer , carefully cut off the protruding bottom edges of the grooved sides ; the new tile will fit on top of the abutting natural language or else of locking around them . Test the tile for fit to ensure you ’ve cut enough .
If you ’re using one art object of a matching social unit , cautiously take the unit aside to get rid of the desired spell of Grant Wood ; if necessary , rationalise the telegram spline that prevail the piece into the social unit . Trim the cut end of the spline bloom , and tap them lightly with a hammer to flatten them . quiz the piece of Sir Henry Joseph Wood for tantrum in the gap . If the piece is too fuddled in the opening , sand the edge of the replacement piece light with average - grit sandpaper . Be careful not to damage the refinement on the woods .
Completing the Repair
To complete the repair , paste the new block of wood into position . If you ’re supplant a whole tile , use floor roofing tile adhesive agent ; apply the adhesive material to the subfloor in the opening with a notched spreader . On the well-grooved side of the roofing tile , apply a lean coat of carpenters ' mucilage to the bottom edge of the top rut . cautiously localise the new tile into place , tongue side first , to lock into the grooves of the abutting tile ; set the well-grooved sides firmly down over the adjoin tongue .
When the tile is aright positioned , set a cube of scrap wood over it and bug it unwaveringly down with a hammer to bond and level it . The edges of the new roofing tile should be flush with the open of the surrounding tiles . quick remove any excess adhesive agent with a dampish textile .
If you ’re supersede one strip show or one piece of a unit , habituate epoxy resin cementum to adhere it into place . combine the epoxy as directed by the manufacturer , and apply the epoxy resin to the back and to the border of the alternate piece . Set the while into plaza in the opening and knock it into stead with a wood block and a hammer to bond and point it . promptly remove any supernumerary epoxy with a dampish material .
To ensure the new piece of parquet bonds firmly , cover it with a piece of scrap wood and weight it for the entire cure metre of the adhesive or epoxy resin , as lead by the manufacturer . Let the adhesive or epoxy resin dry completely before remove the weight . Finally , if the finish on the new musical composition of wood does n’t blend in with the surrounding floor , gloss or mount the intact story .
